Dada is now reseller for DACT & Flashbacksales

only wants the best suppliers.

Developing the Dada 405 amplifier-boards

Joost, who is the development-engineer (and CTO) of Dada/JP Engineering, wanted to give you a first impression of the starting-points why we are developing the new 405 High-end boards.

The boards will be launched in the beginning of 2007. We are developing & testing the prototypes for the moment but we can not publish any pictures yet.

Joost's paper is below.

Stefaan

There are five sources for serious 405 modifications:

• The Quad 405 service manual
• The text from Bernd Ludwig
• The DC-Daylight (Keith Snook) Web pages
• The designs of the Quad 240/306/510/520 and 606 which were all developed during the life cycle of the 405.
• The designs of Tiberiu Vicol

The Quad 405 service manual.

In this manual the history of the 405 in terms of official factory modifications is fully documented. Also are most of the diagrams, part lists and printed circuit board layouts present.

It can give you ideas for retrofitting modifications to the 405-1 and early 405-2 models.

(the 405 service manual is available for free on simple e-mail demand from info@dadaelectronics.eu)

The Bernd Ludwig paper.

Bernd Ludwig was (as far as I know) the first one who described the 405 circuit in full detail, suggested three upgrades and shared a lot of (his) general knowledge about the 405 circuit. The paper covers the following subjects.

1. Changes for the input Opamp circuit
2. Modification of the Current Limiter
3. Extensive output circuit modification
4. General tips and hints concerning the 405 circuit

DC- Daylight Web pages.

Using the work of Bernd Ludwig as a basis, Keith Snook suggested two important modifications:

1. Changing the input Opamp circuit to a non inverting one.
2. Retrofit (my words) the Current Dumper Bridge design of later Quad models to the 405 circuit.

Also Keith suggested more practical ways to implement Bernd Ludwig's modifications, completed the set of diagrams of the 405, introduced his own fully modified 405-3, ( my number) and discovered a fault in the Service Documentation concerning the diagram of the 405-2 current limiter.

The designs of the Quad 240/306/510/520 and 606.

This give you some ideas how a fully developed 405 could look. Quad themselves did only one substantial upgrade, the 405-2 modification.

The designs of Tiberiu Vicol.

Although he made very extensive redesigns, some parts will fit as an upgrade to a more or less normal 405. The quality of his work is very good, so keep track!

The JPE / Dada design.

Instead of producing an endless number of prototypes, during the design stage I decided to built the two circuits, the Non and Inverted input circuit, in a computer simulation tool. I modelled the full input circuit including the mid section filter stage. The rest of the circuit is simulated by a non inverting Opamp. The latter one providing the necessary gain and the DC feedback circuit. See the diagram for details. Both circuits emulate the standard 405 with an input sensitivity of 500mV, and a overall gain of 56.

Some observations:

The gain of the input Opamp circuit is 15, the input impedance is 20K at 1kHz. When changing the gain, you also have to change the time constants of the local and overall feedback loops. When using the model you can play with the values of the components and see the results on the spot. To preserve the overall frequency behaviour, follow the recipe of Bernd Ludwig. If you change some values, i.e. to increase the DC suppression, it also has effects on the LF response. The behaviour of the circuit is plain Opamp technique, no magic or surprises.

With the non inverted input circuit, which is a far better idea as a first stage than a inverted one, you only have to replace two components, to change the gain and the time constant of the overall feedback circuit. In a inverting circuit the noise is higher and in general the input impedance is low. By changing the power supply voltage (asymmetric), testing of the DC feedback circuit can be done. The non inverted model performs ok in this respect. I did not build a complete 405 circuit, I believe the current dumping principle works fine!

Power output of the 405.

Instead of adding power to the 405 by extensive modifications, we advise to combine the two channels of the amplifier, either in serial or parallel mode. You can run our modules without current limiters, but we advise only to do this when the thermal switches are installed. In normal operation the current limiters, based on the 405-2 circuit, will have no audible effect.

The model and our own input gave the following functional/technical demand for the prototype

• Onboard phase inverter for connecting the two channels in serial mode
• Onboard pot for balancing the channels in block mode
• Non inverting input circuit (lower noise)
• Regulated power supply for the Opamps
• Opamps of your choice, starting with OPA604
• Optimized Current Dumper Bridge configuration
• Current limiter on separate PCB’s, can be removed!
• Active ground DC protection circuit instead of Clamp circuit, requires separated PSU
• Input sensitivity jumper select
• Voltage limiter jumper select
• Based on the latest 405-2, without all the layout issues
• Thermal switches to protect the modules from overheating

The power supply

The upgrade that Bernd and Keith suggest is replacing the PSU capacitors with fresh bigger ones and bypassing the capacitors with small caps to reduce the HF impedance. Although this is good advise in itself, we have to take the development of the PSU a step further.

The active ground DC protection will only work with a fully separated double power supply. But the big sonic reason for building a double supply is the following: Crosstalk! A standard 405 have a channel separation of only -60dB at 10KHz. So the crosstalk signal is 20dB higher than the distortion. The double supply in combination with a careful internal cable layout and building the amplifier as a four-pole device, so no ground connections, can reduce the crosstalk level to at least -90dB across the audio spectrum. The four pole approach also reduces ground loops, with a standard 405 there is always a ground loop, formed by the Cinch or Din input cables. For safety reasons the power supply cord must be connected to a wall socket with a proper earth connection, so touching the case is not a hazardous job.

Joost

Dual 405 Power supply & DACT Attenuator

The Dada / JPE Dual Mono power-supply for the Quad 405-1 and 405-2 are available from the Dada Electronics Ebay-webshop now.

See the article below for more technical information about the Dual-mono PSU-board.

The High-end 405 driver-boards will be launched in the coming weeks.

Dada Electronics can now also offer all DACT Audio-grade products and give you advice for using them in existing amplifiers or your own projects.

Count on a delivery-time of +/- 2 weeks for DACT-products that are not in the Ebay-shop yet.

Danish Audio ConnecT-products are the absolute High-end components without compromise. Dada Electronics used them in several Quad & other preamplifiers before with excellent results.

The DACT-picture is (c) www.dact.com

Stefaan

Did Dada / JPE invent the 405 dual PSU?

No.

Hans Bakker did it 15 years ago.

He had to use several 2200MF caps and dual bridge-diodes.

Hans is a lifetime member of Quad Spot by these and he will get a box of Antwerpse Handjes.

Stefaan